PoE splitter 1 to 2 (plastic housing)
PoE extender that extends network and power by up to 100 meters and can connect two PoE devices.
- 1 PoE input and 2 PoE outputs
- Extends PoE and network by up to 100 meters
- 10/100 Mbps network connection
- Powered directly through the PoE cable
- Supports IEEE 802.3af/at
- Can be used with IP cameras, access points and IP phones, among other devices
- Plug and play – requires no configuration
- Can be cascaded for longer cable runs
| Datasheet |
| Technical specifications | |
| Model | IPC9950 |
| Product type | 1-to-2 PoE extender |
| Application | Extends Ethernet data and PoE power and distributes one PoE connection to two PoE devices |
| PoE input | 1 × RJ45 |
| PoE outputs | 2 × RJ45 |
| Number of output channels | 2 |
| Network speed | 10/100 Mbps |
| Transmission distance | Extends Ethernet and PoE by up to an additional 100 m |
| Cascading | Supported; source states extenders can be cascaded for installations up to 700 m |
| Repeater mode | Store-and-forward |
| Switching capacity | 400 Mbps |
| MAC address table | 2K |
| Network protocols | IEEE 802.3i 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3x flow control |
| Connectors | Shielded RJ45, EIA/TIA 568A and 568B |
| Network cable | Shielded Cat5, Cat5e, Cat6 or better |
| PoE | |
| PoE standards | IEEE 802.3af / IEEE 802.3at |
| Input voltage | 44–57 V DC |
| Output voltage | 48 V DC |
| Maximum input power | 30 W |
| Maximum output power | 15 W |
| PoE pinout | 1/2 (+), 3/6 (-), Mode A / End-Span |
| PoE detection | Automatic detection of compatible PoE devices |
| Local power supply | Not required; extender is powered through the PoE input |
| Installation & indicators | |
| Installation | Plug and play, no configuration required |
| LED indicators | Integrated in the RJ45 connectors; power indicator shows when PoE is enabled |
| Recommended environment | Indoor use; for outdoor installation the extender must be installed in a waterproof location |
| Physical & environmental specifications | |
| Dimensions | 90 × 45 × 22 mm |
| Weight | 60 g |
| Operating temperature | -10 °C to +45 °C |
| Operating humidity | Up to 90%, non-condensing |
| Storage humidity | 5–90%, non-condensing |
| MTBF | 100,000 hours at 25 °C |
| Compliance | IEEE 802.3af/at, CE, FCC, RoHS |
| Der tages forbehold for eventuelle fejl og ændringer i specifikationerne / Specifications are subject to change without notice. Errors and omissions excepted. | |
There is no reviews yet. Be the first to write us your opinion
Split the PoE connection to two network devices
This 1 to 2 PoE extender is used when you want to extend an existing PoE connection to two network devices. The extender has one RJ45 port for PoE input and two RJ45 ports for PoE output.
This means that both data and power can be carried through the network cables, so you can, for example, connect IP cameras, access points or IP phones without needing a separate power connection at the extender.
Extends the PoE connection by up to 100 meters
A standard Ethernet cable usually has a maximum range of around 100 meters. With the extender, the connection can be extended by an additional 100 meters while both network data and PoE power are carried onward.
This makes the product suitable for installations where the network device needs to be placed farther away from the PoE switch or PoE injector than a regular cable connection allows.
No local power supply needed
The extender gets power directly through the PoE input. You therefore don’t need a power outlet or separate power supply where the extender is installed.
This can make installation much simpler in places where network cable can already be run, but where there is no access to 230 V nearby.
10/100 Mbps network
The network ports support 10/100 Mbps. This is suitable for many common PoE-based installations with IP cameras, access points, IP phones and other network equipment.
Supports IEEE 802.3af/at PoE
The extender supports IEEE 802.3af/at and operates with a PoE input voltage of DC 44-57 V. Power and data are carried through the network cable, so there is no need to run a separate power cable alongside the Ethernet connection.
PoE is used on pins 1/2 (+) and 3/6 (-), corresponding to Mode A / End-Span.
Plug and play without configuration
No software or network configuration is required to start using the extender. Connect the PoE connection to the input and the desired network devices to the outputs.
The LED indicators by the RJ45 connectors make it possible to see the PoE status directly on the unit.
Can be used for longer cable runs
PoE extenders can be cascaded when the connection needs to be carried over longer distances. According to the specifications, multiple extenders can be combined for installations with a total range of up to 700 meters. The practical possible distance and available PoE power depend, among other things, on the power supply, the number of extenders, cable length and the power consumption of the connected equipment.
For indoor installation
The extender is recommended for indoor use and must be kept away from moisture and water. If used outdoors, it must be mounted in a location protected from water.
Technical key points
- PoE input: 1 x RJ45
- PoE output: 2 x RJ45
- Network speed: 10/100 Mbps
- PoE standard: IEEE 802.3af/at
- Input voltage: DC 44-57 V
- Output voltage: 48 V
- Max. stated input power: 30 W
- Max. stated output power: 15 W
- PoE pins: 1/2 (+), 3/6 (-)
- PoE type: Mode A / End-Span
- Extension: up to 100 meters per extender
- Network cable: Cat5, Cat5e, Cat6 or better
- Repeater function: Store and forward
- MAC address table: 2K
- Switching capacity: 400 Mbps
- Network standards: IEEE 802.3i, IEEE 802.3u and IEEE 802.3x
- Operating temperature: -10 °C to 45 °C
- Operating humidity: up to 90%, non-condensing
- MTBF: 100,000 hours at 25 °C
- Dimensions: 90 x 45 x 22 mm
- Weight: 60 g
- Compliance: RoHS, CE and FCC
